- NVR008.jpg (16.27 КБ) 11669 просмотров
U-Boot 2010.06-svn6166 (Aug 06 2014 - 17:10:23)
Check spi flash controller v350... Found
Spi(cs1) ID: 0xEF 0x40 0x19 0x00 0x00 0x00
Spi(cs1): Block:64KB Chip:32MB Name:"W25Q256FV"
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Hisilicon ETH net controler
inner_phy = 1!!
32768 KiB hi_sfc at 0:0 is now current device
jpeg decoding ...
mmu_enable
decode success!!!!
decode jpeg!
dev 0 set background color!
dev 2 set background color!
dev 0 opened!
graphic layer 0 opened!
dev 2 opened!
graphic layer 2 opened!
[V7]ChipSet is HI3520D.
no uid
[V7]ChipSet is HI3520D.
[V7]ChipSet is HI3520D.
Hisilicon ETH net controler
miiphy_register: non unique device name '0:3'
miiphy_register: non unique device name '0:2'
inner_phy = 1!!
MAC: 5A-57-16-2D-2C-44
eth_set_host_mac_address
UP_PORT : phy status change : LINK=DOWN : DUPLEX=FULL : SPEED=100M
Up/Down PHY not link!
Hit CTRL+C to stop autoboot: 3 0
hisilicon # 111 ру help
? - alias for 'help'
base - print or set address offset
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
cmp - memory compare
cp - memory copy
crc32 - checksum calculation
ddrp - ddrp training tools v200
ddrt - ddr training tools v200
decjpg - jpgd - decode jpeg picture.
erase_env- erase_env - erase env
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
getinfo - print hardware information
go - start application at address 'addr'
help - print command description/usage
loadb - load binary file over serial line (kermit mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
md - memory display
mii - MII utility commands
mm - memory modify (auto-incrementing address)
mtest - simple RAM read/write test
mw - memory write (fill)
nm - memory modify (constant address)
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
saveenv - save environment variables to persistent storage
setenv - set environment variables
setvobg - setvobg - set vo backgroud color.
- setvobg [dev color]
sf - SPI flash sub-system
startgx - startgx - open graphics layer.
- startgx [layer addr stride x y w h]
startvo - startvo - open interface of vo device.
- startvo [dev type sync]
stopgx - stopgx - close graphics layer.
- stopgx [layer]
stopvo - stopvo - close interface of vo device.
- stopvo [dev]
tftp - tftp - download or upload image via network using TFTP protocol
unittest- unittest type
update - update - update image
usb - USB sub-system
usbboot - boot from USB device
version - print monitor version
hisilicon # printenv
bootargs=mem=130M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfstype=jffs2 mtdparts=hi_sfc:512k(boot),2560k(kernel),29440k(rootfs),256k(logo)
bootdelay=3
baudrate=115200
ipaddr=192.168.1.10
serverip=192.168.1.1
netmask=255.255.255.0
bootfile="uImage"
bootcmd=setenv bootargs ${bootargs} macaddr=${ethaddr}; sf probe 0;sf read 0x82000000 0x80000 0x280000;bootm 0x82000000
logover=.nvr.mini
uver=.nvr.mini
kver=.nvr.mini
fver=.nvr.mini
stdin=serial
stdout=serial
stderr=serial
verify=n
vobuf=0x94000000
jpeg_size=0x40000
jpeg_addr=0x94000000
ethaddr=5a:57:16:2d:2c:44
ver=U-Boot 2010.06-svn6166 (Aug 06 2014 - 17:10:23)
Environment size: 621/65532 bytes
Spi(cs1):
Block:64KB
Chip:32MB
Name:"W25Q256FV"
spi size: 0x33554432
chip num: 1
4 cmdlinepart partitions found on MTD device hi_sfc
Creating 4 MTD partitions on "hi_sfc":
0x000000000000-0x000000080000 : "boot"
0x000000080000-0x000000300000 : "kernel"
0x000000300000-0x000001fc0000 : "rootfs"
0x000001fc0000-0x000002000000 : "logo"
