NVR N6100-16EH не видно в сети.

[yuri1958]

Регистратор стартует нормально. При включении загорается зеленый светодиод на сетевом разъеме. По сети не видится. Сетевой чип RTL8211EG тепленький. С чего начать менять чип или сетевой транс?

[VirtualLink]

Вначале вот так, а потом логи посмотришь!

[yuri1958]

Вначале вот так, а потом логи посмотришь!

Такого инструмента в хозяйстве не нашел . Снял лог загрузки с помощью уарт.



U-Boot 2010.06 (May 06 2014 - 20:57:31)

NAND: Check nand flash controller v504. found
Special NAND id table Version 1.36
Nand ID: 0xAD 0xF1 0x80 0x1D 0xAD 0xF1 0x80 0x1D
Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:4bits/512Byte
128 MiB
Check spi flash controller v350... Found
Can't find a valid spi flash chip.
Can't find a valid spi flash chip.
*** Warning - bad CRC or NAND, using default environment

In: serial
Out: serial
Err: serial
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found

NAND read: device 0 offset 0x7c00000, size 0x40000
262144 bytes read: OK
mmu_enable
<<imgwidth=1024, imgheight=768, linebytes=2048>>
decode success!!!!
dev 0 set background color!
dev 2 set background color!
dev 0 opened!
dev 2 opened!
graphic layer 0 opened!
graphic layer 2 opened!
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x100000, size 0x300000
3145728 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.4.35_hi3535
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2845328 Bytes = 2.7 MiB
Load Address: 80008000
Entry Point: 80008000
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0
Linux version 3.4.35_hi3535 (root@sqy-desktop) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread)) ) #96 SMP Mon Oct 13 11:05:21 CST 2014
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: hi3535
Truncating memory at 0x80000000 to fit in 32-bit physical address space
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 7 pages/cpu @c087c000 s6528 r8192 d13952 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 48768
Kernel command line: mem=192M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfstype=yaffs2 mtdparts=hinand:1M(uboot),3M(kernel),90M(rfs),20M(app),10M(config),4M(logo)
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 192MB = 192MB total
Memory: 187648k/187648k available, 8960k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xcc800000 - 0xff000000 ( 808 MB)
lowmem : 0xc0000000 - 0xcc000000 ( 192 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc0677000 (6588 kB)
.init : 0xc0677000 - 0xc06a4980 ( 183 kB)
.data : 0xc06a6000 - 0xc06d6d20 ( 196 kB)
.bss : 0xc06d6d44 - 0xc06f8ac4 ( 136 kB)
SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:128
sched_clock: 32 bits at 62MHz, resolution 16ns, wraps every 68719ms
Console: colour dummy device 80x30
Calibrating delay loop... 1987.37 BogoMIPS (lpj=9936896)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Initializing cgroup subsys freezer
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
Setting up static identity map for 0x8052cba0 - 0x8052cbd4
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c9, AUX_CTRL 0x72430001, Cache size: 262144 B
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated (3981.31 BogoMIPS).
NET: Registered protocol family 16
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 40) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 41) is a PL011 rev2
uart:2: ttyAMA2 at MMIO 0x200a0000 (irq = 42) is a PL011 rev2
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource timer0
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.30 [Flags: R/W DEBUG].
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.18)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
msgmni has been set to 366
encryption fail
no need alpu
no ack
sha204_sn is 1
sha204_sn is 23
sha204_sn is 5e
sha204_sn is 24
sha204_sn is a2
sha204_sn is 62
sha204_sn is a1
sha204_sn is 15
sha204_sn is ee
sha204_devinfo is 44 i is 0
sha204_devinfo is 56 i is 1
sha204_devinfo is 52 i is 2
sha204_devinfo is 32 i is 3
sha204_devinfo is 33 i is 4
sha204_devinfo is 35 i is 5
sha204_devinfo is 31 i is 6
sha204_devinfo is 35 i is 7
sha204_devinfo is 30 i is 8
sha204_devinfo is 34 i is 9
sha204_devinfo is 1 i is 10
sha204_devinfo is 5c i is 11
sha204_devinfo is 0 i is 12
sha204_devinfo is 0 i is 13
sha204_devinfo is 0 i is 14
sha204_devinfo is 0 i is 15
TempKey is 4b
TempKey is 49
TempKey is de
TempKey is 3d
TempKey is 37
TempKey is c2
TempKey is b
TempKey is 16
TempKey is a4
TempKey is 90
TempKey is a4
TempKey is 7c
TempKey is fc
TempKey is f1
TempKey is ed
TempKey is 41
TempKey is b4
TempKey is ea
TempKey is ad
TempKey is ec
TempKey is 30
TempKey is 23
TempKey is de
TempKey is 2f
TempKey is ab
TempKey is b3
TempKey is bd
TempKey is e3
TempKey is 4a
TempKey is 24
TempKey is a8
TempKey is b
encryption ok
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
loop: module loaded
ahci: SSS flag set, parallel bus scan disabled
ahci ahci.0: AHCI 0001.0300 32 slots 3 ports 6 Gbps 0x7 impl platform mode
ahci ahci.0: flags: ncq sntf stag pm led clo only pmp fbs slum part ccc sxs boh
scsi0 : ahci_platform
scsi1 : ahci_platform
scsi2 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x12010000-0x1201ffff] port 0x100 irq 63
ata2: SATA max UDMA/133 mmio [mem 0x12010000-0x1201ffff] port 0x180 irq 63
ata3: SATA max UDMA/133 mmio [mem 0x12010000-0x1201ffff] port 0x200 irq 63
Spi id table Version 1.22
Found Nand Flash Controller V504.
Nand ID: 0xAD 0xF1 0x80 0x1D 0xAD 0xF1 0x80 0x1D
Nand: Hynix NAND 128MiB 3,3V 8-bit
Nand(Hardware): Block:128KB Page:2KB OOB:64B ECC:4bits/512Byte Chip:128MB*1
6 cmdlinepart partitions found on MTD device hinand
6 cmdlinepart partitions found on MTD device hinand
Creating 6 MTD partitions on "hinand":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000400000 : "kernel"
0x000000400000-0x000005e00000 : "rfs"
0x000005e00000-0x000007200000 : "app"
ata1: SATA link down (SStatus 0 SControl 300)
0x000007200000-0x000007c00000 : "config"
0x000007c00000-0x000008000000 : "logo"
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver rt2800usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 54, io mem 0x10040000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
hiusb-ohci hiusb-ohci.0: irq 53, io mem 0x10030000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
xhci-hcd hiusb3.0: xHCI Host Controller
xhci-hcd hiusb3.0: new USB bus registered, assigned bus number 3
xhci-hcd hiusb3.0: irq 64, io mem 0x12000000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
xhci-hcd hiusb3.0: xHCI Host Controller
xhci-hcd hiusb3.0: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
registered taskstats version 1
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
yaffs: dev is 32505858 name is "mtdblock2" rw
yaffs: passed flags ""
VFS: Mounted root (yaffs2 filesystem) on device 31:2.
Freeing init memory: 180K

_ _ _ _ _ _ _ _ _ _ _ _
\ _ _ _ _ _ ___
/ /__/ \ |_/
/ __ / - _ ___
/ / / / / /
_ _ _ _/ / / \_/ \_ ______
___________\___\__________________

[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
udevd (595): /proc/595/oom_adj is deprecated, please use /proc/595/oom_score_adj instead.
[RCS]: /etc/init.d/S02toe
STMMAC driver:
platform registration...
done!
Set system config register 0x200300ec with value 0x003f003f
done!
DWMAC1000 - user ID: 0x10, Synopsys ID: 0x36
Enhanced descriptor structure
MACADDR in get is 0:0:0:0:0:0
no valid MAC address for MAC 0;please, use ifconfig or nwhwconfig!
eth0 - (dev. name: stmmaceth - id: 0, IRQ #59
IO base addr: 0xfe0a0000)
smiInit ok
STMMAC MII Bus: probed
eth0: PHY ID 00000000 at 30 IRQ -6 (1:1e) active
eth0: PHY ID 00000000 at 31 IRQ 0 (1:1f)
DWMAC1000 - user ID: 0x10, Synopsys ID: 0x36
Enhanced descriptor structure
MACADDR in get is 0:0:0:0:0:0
no valid MAC address for MAC 1;please, use ifconfig or nwhwconfig!
eth1 - (dev. name: stmmaceth - id: 0, IRQ #59
IO base addr: 0xfe0a4000)
eth1: PHY ID 00000000 at 30 IRQ -6 (1:1e)
eth1: PHY ID 00000000 at 31 IRQ 0 (1:1f) active
stmmac_reset: RESET COMPLETE!

**************************************************
* TNK driver built on Sep 9 2014 at 17:16:30
* TNK driver mode is TOE
**************************************************
stmmac: Rx Checksum Offload Engine supported
stmmac: Rx Checksum Offload Engine supported
switchmac_init success
[RCS]: /etc/init.d/S03ants
Hisilicon Media Memory Zone Manager
hi3535_base: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Hisilicon UMAP device driver interface: v3.00
load sys.ko for Hi3535...OK!
Load tde.ko ...OK!
load vgs.ko for Hi3535...OK!
load venc.ko for Hi3535...OK!
load chnl.ko for Hi3535...OK!
load h264e.ko for Hi3535...OK!
load rc.ko for Hi3535...OK!
load jpege.ko for Hi3535...OK!
load vou.ko ....OK!
load vpss.ko ....OK!
load vda.ko ....OK!
load region.ko ....OK!
load vdec.ko ....OK
load vhd firmware.ko OK
load hdmi.ko ....OK!
Load hi3535_jpegd.ko success. (SDK_VERSION:[jpeg6bv1.0] Build Time:[Feb 27 2014, 20:11:08])
insmod: can't insert 'extdrv/rt5370sta.ko': No such file or directory
usbcore: registered new interface driver option
USB Serial support registered for GSM modem (1-port)
acodec inited!
rm: can't remove '/usr/etc/config.tar.gz': No such file or directory
mkdir: can't createth1: generated random MAC address b6:c0:2c:67:ed:08
e directory '/usr/etc/ppp': File exists
mkdir: can't create directory '/usr/etc/ppp/peeMACADDR in set is b6:c0:2c:67:ed:8
rs': File exists
mv: can't rename '/root/sysinit': No such file or directory
/etc/init.d/S03ants: line 33: /etc/startusb: not found
[RCS]: /etc/init.d/S80network
Auto login as root ...
May 5 10:49:04 login[971]: root login on 'ttyS000'
Welcome to HiLinux.
None of nfsroot found in cmdline.
# begin dvr//////////////////////////////////////////////////////////////
argc 2, argv ./ants_dvr
open /usr/etc/mycfg.xml

open /root/res_xml/Keyboard.xml

open /tmp/qtembedded-0//fonts//fontdb.tmp

open /usr/local/Trolltech/QtEmbedded-4.6.3-arm/lib/fonts/gulim_17_50.qpf2

open /usr/local/Trolltech/QtEmbedded-4.6.3-arm/lib/fonts/microsoft_sans_serif_12_75.qpf2

open /usr/local/Trolltech/QtEmbedded-4.6.3-arm/lib/fonts/yh_17_50.qpf2

DBG[embedded/qscreenlinuxfb_qws.cpp connect--350] QLinuxFbScreen::connect :0
DBG[embedded/qscreenlinuxfb_qws.cpp connect--379]
open /dev/fb0

DBG[embedded/qscreenlinuxfb_qws.cpp connect--397] open device /dev/fb0 success
DBG[embedded/qscreenlinuxfb_qws.cpp connect--425]
open /usr/etc/mycfg.xml

open /root/DeviceDisplay.xml

DBG[embedded/qscreenlinuxfb_qws.cpp connect--469] vinfo.xres 1024 768
DBG[embedded/qscreenlinuxfb_qws.cpp connect--481] d_ptr->fd 8 vinfo xres 1024, xres_virtual1024
DBG[embedded/qscreenlinuxfb_qws.cpp connect--513] screen vinfo
bits_per_pixel 32
r g b 8 8 8
d = 32
finfo.line_length 2560
DBG[embedded/qscreenlinuxfb_qws.cpp connect--554] dw is 1024,dh is 768 lstep 4096
DBG[embedded/qscreenlinuxfb_qws.cpp connect--600]

mmap fb0 : d_ptr->fd 8, data -1244831744, mapsize 8294400

open /dev/tty0

newMouseHandler mouseProto auto, mouseDev/dev/mouse0

erro[embedded/qmousedriverfactory_qws.cpp create--111]

erro[embedded/qmousedriverfactory_qws.cpp create--114]

erro[embedded/qmousedriverfactory_qws.cpp create--117]

open /dev/psaux

open /dev/input/mice

QWSTtyKeyboardHandler /dev/ttyS2
kbdType RS485
open /dev/hi_gpio

open /dev/ttyS1

termdata.c_iflag 5
termdata.c_oflag 0
termdata.c_cflag b0
termdata.c_lflag 0
termdata.c_ispeed be9c6340
termdata.c_ospeed b6fd8000
termdata.c_line 0
termdata.c_cc 0 0
kbdType gpioMini
open /dev/hi_gpio

open /usr/etc/mycfg.xml

open /usr/etc/mycfg.xml

open /root/res/language_Russian.qm

open /root/res/LanguageInfo.xml

open /root/res/default.qss

font=efont
font-size=16
from config -> font=efont
from config -> font-size=16
QLayout: Attempting to add QLayout "" to informationFrame "IMShowMain", which already has a layout
open ./pinyin/english.xml

open /root/res/cursor.png

open /root/res/cursor.png

open /usr/etc/mycfg.xml

open /root/res/pre_enlarge.png

open /root/res/label_Mouse.png

open /root/res/enlarge.png

open /root/res/shrink.png

open /root/res/up_Mouse.png

open /root/res/down_Mouse.png

open /root/res/left_Mouse.png

open /root/res/right_Mouse.png

open /root/res/up_left_Mouse.png

open /root/res/up_right_Mouse.png

open /root/res/down_left_Mouse.png

open /root/res/down_right_Mouse.png

QImage::pixel: coordinate (10,6) out of range
QImage::pixel: coordinate (10,7) out of range
QImage::pixel: coordinate (10,8) out of range
QImage::pixel: coordinate (10,9) out of range
QImage::pixel: coordinate (10,10) out of range
QImage::pixel: coordinate (10,11) out of range
QImage::pixel: coordinate (10,12) out of range
QImage::pixel: coordinate (10,13) out of range
QImage::pixel: coordinate (10,14) out of range
QLayout: Attempting to add QLayout "" to CDeviceTime "CDeviceTime", which already has a layout
QLayout: Attempting to add QLayout "" to CQRCode "", which already has a layout
QLayout: Attempting to add QLayout "" to DlgDragChannel "", which already has a layout
open /root/res/pre_recordState.png

QLayout: Attempting to add QLayout "" to SysRecover "", which already has a layout
QLayout: Attempting to add QLayout "" to SysRecover "", which already has a layout
QImage::pixel: coordinate (10,6) out of range
QImage::pixel: coordinate (10,7) out of range
QImage::pixel: coordinate (10,8) out of range
QImage::pixel: coordinate (10,9) out of range
QImage::pixel: coordinate (10,10) out of range
QImage::pixel: coordinate (10,11) out of range
QImage::pixel: coordinate (10,12) out of range
QImage::pixel: coordinate (10,13) out of range
QImage::pixel: coordinate (10,14) out of range
open /root/res/play_left.png

open /root/res/play_play.png

open /root/res/play_noVideo.png

open /root/res/play_stop.png

open /root/res/play_sound.png

open /root/res/play_fast.png

open /root/res/play_slow.png

open /root/res/play_capture.png

open /root/res/play_backup.png

open /root/res/play_frame.png

open /root/res/play_fullscreen.png

QWidget::setLayout: Attempting to set QLayout "horizontalLayout_2" on DlgScreenInfo "DlgScreenInfo_UI", when the QLayout already has a parent
open /root/res/ptz_back.png

open /root/res/ptz_up.png

open /root/res/ptz_up_Hover.png

open /root/res/ptz_up_press.png

open /root/res/ptz_down.png

open /root/res/ptz_down_Hover.png

open /root/res/ptz_down_press.png

open /root/res/ptz_left.png

open /root/res/ptz_left_Hover.png

open /root/res/ptz_left_press.png

open /root/res/ptz_right.png

open /root/res/ptz_right_Hover.png

open /root/res/ptz_right_press.png

open /root/res/ptz_left_top.png

open /root/res/ptz_left_top_Hover.png

open /root/res/ptz_left_top_press.png

open /root/res/ptz_right_top.png

open /root/res/ptz_right_top_Hover.png

open /root/res/ptz_right_top_press.png

open /root/res/ptz_left_down.png

open /root/res/ptz_left_down_Hover.png

open /root/res/ptz_left_down_press.png

open /root/res/ptz_right_down.png

open /root/res/ptz_right_down_Hover.png

open /root/res/ptz_right_down_press.png

open /root/res/ptz_auto.png

open /root/res/ptz_auto_hover.png

open /root/res/ptz_auto_press.png

open /root/res/ptz_minus.png

open /root/res/ptz_plus.png

QLayout: Attempting to add QLayout "" to DlgAutoIP "", which already has a layout
open /root/res/pre_AudioOpen.png

open /root/res/pre_AudioClose.png

open /root/res/pre_DiskNormal.png

open /root/res/pre_DiskNormal.png.bmp

open /root/res/pre_DiskNormal.png.jpeg

open /root/res/pre_DiskNormal.png.jpg

open /root/res/pre_DiskNormal.png.pbm

open /root/res/pre_DiskNormal.png.pgm

open /root/res/pre_DiskNormal.png.png

open /root/res/pre_DiskNormal.png.ppm

open /root/res/pre_DiskNormal.png.xbm

open /root/res/pre_DiskNormal.png.xpm

open /root/res/pre_DiskFull.png

open /root/res/pre_DiskFull.png.bmp

open /root/res/pre_DiskFull.png.jpeg

open /root/res/pre_DiskFull.png.jpg

open /root/res/pre_DiskFull.png.pbm

open /root/res/pre_DiskFull.png.pgm

open /root/res/pre_DiskFull.png.png

open /root/res/pre_DiskFull.png.ppm

open /root/res/pre_DiskFull.png.xbm

open /root/res/pre_DiskFull.png.xpm

open /root/res/pre_DiskNull.png

open /root/res/pre_DiskNull.png.bmp

open /root/res/pre_DiskNull.png.jpeg

open /root/res/pre_DiskNull.png.jpg

open /root/res/pre_DiskNull.png.pbm

open /root/res/pre_DiskNull.png.pgm

open /root/res/pre_DiskNull.png.png

open /root/res/pre_DiskNull.png.ppm

open /root/res/pre_DiskNull.png.xbm

open /root/res/pre_DiskNull.png.xpm

QPixmap::scaled: Pixmap is a null pixmap
QPixmap::scaled: Pixmap is a null pixmap
QPixmap::scaled: Pixmap is a null pixmap
open /root/res/pre_alarm1.png

open /root/res/pre_alarm2.png

open /root/res/pre_Disk.png

open /root/res/pre_Disk.png.bmp

open /root/res/pre_Disk.png.jpeg

open /root/res/pre_Disk.png.jpg

open /root/res/pre_Disk.png.pbm

open /root/res/pre_Disk.png.pgm

open /root/res/pre_Disk.png.png

open /root/res/pre_Disk.png.ppm

open /root/res/pre_Disk.png.xbm

open /root/res/pre_Disk.png.xpm

[Mid] start init
system:/root/nvr_daemon &
system:killall -9 ntpd;ntpd -l
killall: ntpd: no process killed
[Mid] load custom cfg
1
load host proto /root/host_libs/libcloud.so
[WEBSDK][../../src/AntsWebSDK.c:ants_HostMgr_Lib_GetFxns:776:time:14:56:26]Start================================[WebServer] SUCCESS
load host proto /root/host_libs/libwebserver.so
[DANA-I][ants_HostMgr_Lib_GetFxns:3614]Get Fxns Name[Dana] ID[17]
load host proto /root/host_libs/libdana.so
pAntsDVRInfo->byChanNum = 0 byDecodeChans = 16
!!pAntsDVRInfo->byChanNum = 0 byDecodeChans = 16 LocalChannelnum= 16
[enable] all
[disable] all
load ipc proto /root/ipc_libs/libi8.so
load ipc proto /root/ipc_libs/libonvif.so
load ipc proto /root/ipc_libs/libi8s.so
load ipc proto /root/ipc_libs/libi9.so
dwRecordChnum = 16
byDecodeChans = 4 dwRealDecodeChnNum = 16 bDeviceInfo_AuxRecord = 0 dwDecodChnNum = 4
******MidLibInfo.dwTotalChnNum = 16,[1,15c,2] 16
[ANTS_DVR_LogicLayer_Init.4637.zero]Support = 1
[ANTS_DVR_LogicLayer_Init.4666.zero]ANTS_Sys_EncSetZeroCodecPara nRet = 0
system:rm -fr /tmp/sata
No such file or directoryNo PTZ protocol existerror:new serial protocol base err.
splib not init
splib not init
splib not init[M[GPIO] GPIOGET_WATCHDOG Enable chardata = 1!!!
ID] net server load...
killall wpa_supplicant
killall: wpa_supplicant: no process killed
chmod: /usr/etc/var: No such file or directory
chmod: /etc/ppp/resolv.conf: No such file or directory
[I8-Server] [src/AntsServerSDK.cpp:7747:GSVRLoadDDNSLib] Load ddns proto /root/ddns_libs/libddns_peanuthull.so
[I8-Server] [src/AntsServerSDK.cpp:7747:GSVRLoadDDNSLib] Load ddns proto /root/ddns_libs/libddns_dyndns.so
[I8-Server] [src/AntsServerSDK.cpp:7747:GSVRLoadDDNSLib] Load ddns proto /root/ddns_libs/libddns_dnsdynamic.so
[I8-Server] [src/AntsServerSDK.cpp:7747:GSVRLoadDDNSLib] Load ddns proto /root/ddns_libs/libddns_noip.so
[I8-Server] [src/AntsServerSDK.cpp:7747:GSVRLoadDDNSLib] Load ddns proto /root/ddns_libs/libddns_3322.so
[src/AntsServerSDK.cpp:00007915:GSVRInitDVR] GetDeviceType Result[33643536] DeviceType[NVR-15C-16CH]
[src/AntsServerSDK.cppset_mac_addr] offset->8 sn->015c012315a162a2245e
[src/AntsServerSDK.cpp:4003:set_mac_addr] MacAddrUnit ->a1 MacAddr->0xa1
[src/AntsServerSDK.cpp:4003:set_mac_addr] MacAddrUnit ->62 MacAddr->0x62
[src/AntsServerSDK.cpp:4003:set_mac_addr] MacAddrUnit ->a2 MacAddr->0xa2
[src/AntsServerSDK.cpp:4003:set_mac_addr] MacAddrUnit ->24 MacAddr->0x24
[src/AntsServerSDK.cpp:4003:set_mac_addr] MacAddrUnit ->5e MacAddr->0x5e
[src/AntsServerSDK.cpp:4012:set_mac_addr] mac addr->0x00:0xa1:0x62:0xa2:0x24:0x5e
[I8-Server] [src/AntsServerSDK.cpp:4025:set_mac_addr] ifconfig eth1 down
[I8-Server] [src/AntsServerSDK.cpp:4091:set_mac_addr] ifconfig eth1 hw ether 0:a1:62:a2:24:5e
MACADDR in set is 0:a1:62:a2:24:5e
[I8-Server] [src/AntsServerSDK.cpp:4154:set_mac_addr] ifconfig eth1 192.168.1.188 netmask 255.255.255.0
MACADDR in set is 0:a1:62:a2:24:5e
[I8-Server] [src/AntsServerSDK.cpp:4246:set_mac_addr] route add default gw 192.168.1.1 eth1
[I8-Server] [src/AntsParameter.cpp:183:InitializeDDNSAbility] ddns[1] [DynDns]->[members.dyndns.org:80]
[I8-Server] [src/AntsParameter.cpp:183:InitializeDDNSAbility] ddns[2] [PeanutHull]->[ddns.oray.org:80]
[I8-Server] [src/AntsParameter.cpp:183:InitializeDDNSAbility] ddns[3] [No-IP]->[dynupdate.no-ip.com:80]
[I8-Server] [src/AntsParameter.cpp:183:InitializeDDNSAbility] ddns[4] [3322]->[members.3322.org:80]
[I8-Server] [src/AntsParameter.cpp:183:InitializeDDNSAbility] ddns[7] [DnsDynamic]->[www.dnsdynamic.org:80]
ERROR: PPP link is not active on ppp0
route: SIOCDELRT: No such device
[MID] ARP server load...
[MID] ARP server load...ok
[MID] nvr ipcs load...
[MID] nvr ipcs load...ok
[MID] nvr host load...
[WEBSDK][../../src/AntsWebCommon.c:Initia_DeviceInfo:81:time:14:56:25]g_struWebSiteSDKInfo.g_ChanNum===============================[16]
[WEBSDK][../../src/AntsWebCommon.c:Initia_DeviceInfo:82:time:14:56:25]g_struWebSiteSDKInfo.g_DVRType===============================[2]
[WEBSDK][../../src/AntsWebCommon.c:Initia_DeviceInfo:83:time:14:56:25]g_struWebSiteSDKInfo.g_AlarmOutPortNum=======================[0]
[WEBSDK][../../src/AntsWebCommon.c:Initia_DeviceInfo:84:time:14:56:25]g_struWebSiteSDKInfo.g_AlarmInPortNum========================[0]
[WEBSDK][../../src/AntsWebCommon.c:Initia_DeviceInfo:85:time:14:56:25]g_struWebSiteSDKInfo.g_byStartChan===========================[0]
[WEBSDK][../../src/AntsWebCommon.c:Initia_DeviceInfo:86:time:14:56:25]g_struWebSiteSDKInfo.sSerialNumberm==========================[015c012315a162a2245e]
[WEBSDK][../../src/AntsWebCommon.c:Initia_DeviceInfo:94:time:14:56:25]g_struWebSiteSDKInfo.wDVRPort================================[5050]
[WEBSDK][../../src/AntsWebCommon.c:Initia_DeviceInfo:95:time:14:56:25]g_struWebSiteSDKInfo.wHttpPort===============================[80]
[WEBSDK][../../src/AntsWebCommon.c:Initia_DeviceInfo:96:time:14:56:25]g_struWebSiteSDKInfo.wHttpsPort==============================[4433]
[WEBSDK][../../src/AntsWebSDK.c:ANTS_WEB_Start:503:time:14:56:26]Server Start
[WEBSDK][../../src/AntsWebSDK.c:initWebs:111:time:14:56:26]Call Begin
[WEBSDK][../../src/AntsWebSDK.c:initWebs:181:time:14:56:26]AntsWebSDK[/root/web/www]
[WEBSDK][../../src/AntsWebSDK.c:initWebs:410:time:14:56:26]Call End
[WEBSDK][../../src/AntsWebSDK.c:ANTS_WEB_Start:527:time:14:56:26]wHttpPort[80]
[WEBSDK][../../src/AntsWebSDK.c:ANTS_WEB_Start:528:time:14:56:26]websSSLOpen[4433]
[WEBSDK][../../src/AntsWebSDK.c:gfxFlashCheckPolicyThread:58:time:14:56:26]======waiting for client's request======
[WEBSDK][../../src/AntsWebSDK.c:ANTS_WEB_Start:547:time:14:56:26]Server Finish
[WEBSDK][../../src/AntsWebSDK.c:AntsHostMgrLibStart:743:time:14:56:26]AntsHostMgrLibStart================================[1] SUCCESS
[MID] nvr host load.ok..
[MID] nvr rtsp/onvif/rtmp server load...
[MID] nvr rtsp/onvif/rtmp server load...ok
killall wpa_supplicant
[18:49:17.865739] local port = 38800
[18:49:17.866366] glnk_init end!
[18:49:17.866618] TSI_SetStatus:328: statue [0] -> [1] 2096
[18:49:17.866667] TSI_SetStatus:328: statue [1] -> [3] 2133
Ants_RTMPServer_Start !!!!!!!!!!!!!!!!!!!!!!!!!!!!! 1935
[INFO.Ants_RTMPServer_Start.65]Ants_RTMPServer_Start start!
[INFO.Ants_RTMPServer_Start.83]create i 1 start!
[RTMP] [server/server.cpp:00002177:Start] Start ok!
[RTMP] [server/server.cpp:00002221:StartListenThread] Create Listen Thread OK
[INFO.ListenProc.2443]ListenProc start!
[INFO.Ants_RTMPServer_Start.87]create i 1 end!
[INFO.Ants_RTMPServer_Start.97]hRtmpHandle = 1!
[INFO.Ants_RTMPServer_Start.101]Ants_RTMPServer_Start end!
[INFO.Ants_RTMPServer_SetStreamCallBack.138]Ants_RTMPServer_SetStreamCallBack start!
[INFO.Ants_RTMPServer_SetStreamCallBack.156]Ants_RTMPServer_SetStreamCallBack end!
Ants_RTMPServer_Start !!!!!!!!!!!!!!!!!!!!!!!!!!!!! 1935 ok
Ants_RTSPServer_Start !!!!!!!!!!!!!!!!!!!!!!!!!!!!! 554
killall: wpa_supplicant: no process killed
open /usr/etc/myExceptionState.xml

erro[antsMainDlg.cpp timerEvent--3155] STOP_DVR_ILLEGAL poweroff?
open /usr/etc/myExceptionState.xml

[IPCMgrThreadAll.7706] new i = 0
[IPCMgrThreadAll.7706] new i = 1
[IPCMgrThreadAll.7706] new i = 2
[IPCMgrThreadAll.7706] new i = 3
[IPCMgrThreadAll.7706] new i = 4
[IPCMgrThreadAll.7706] new i = 5
[IPCMgrThreadAll.7706] new i = 6
[IPCMgrThreadAll.7706] new i = 7
local mac[0] [ff ff ff ff ff ff]
local mac[1] [0 a1 62 a2 24 5e]
erro[preview/preview.cpp SysAudio--4421] no right stopAudio
GUI --> [0/0] dwAbilityType= 2305 bsupp = 1
GUI --> [1/1] dwAbilityType= 2306 bsupp = 1
GUI --> [2/2] dwAbilityType= 2307 bsupp = 1
GUI --> [3/3] dwAbilityType= 2308 bsupp = 1
GUI --> [4/4] dwAbilityType= 2309 bsupp = 1
GUI --> [5/5] dwAbilityType= 2310 bsupp = 1
GUI --> [6/6] dwAbilityType= 2311 bsupp = 1
GUI --> [7/7] dwAbilityType= 2312 bsupp = 1
QLinuxFbScreen::disconnect




munmap 8294400
DBG[embedded/qscreenlinuxfb_qws.cpp connect--350] QLinuxFbScreen::connect /dev/fb0
DBG[embedded/qscreenlinuxfb_qws.cpp connect--379]
open /dev/fb0

DBG[embedded/qscreenlinuxfb_qws.cpp connect--397] open device /dev/fb0 success
DBG[embedded/qscreenlinuxfb_qws.cpp connect--425]
open /usr/etc/mycfg.xml

open /root/DeviceDisplay.xml

DBG[embedded/qscreenlinuxfb_qws.cpp connect--469] vinfo.xres 1024 768
DBG[embedded/qscreenlinuxfb_qws.cpp connect--481] d_ptr->fd 8 vinfo xres 1024, xres_virtual1024
DBG[embedded/qscreenlinuxfb_qws.cpp connect--513] screen vinfo
bits_per_pixel 32
r g b 8 8 8
d = 32
finfo.line_length 2560
DBG[embedded/qscreenlinuxfb_qws.cpp connect--554] dw is 1024,dh is 768 lstep 4096
DBG[embedded/qscreenlinuxfb_qws.cpp connect--600]

mmap fb0 : d_ptr->fd 8, data -1244831744, mapsize 8294400

open /root/res/pre_capture.png

open /root/res/pre_start.png

open /root/res/pre_screen.png

open /root/res/pre_ptz.png

open /root/res/pre_config.png

open /root/res/pre_playback.png

open /root/res/pre_backup.png

open /root/res/pre_alarm.png

open /root/res/pre_file.png

open /root/res/pre_record.png

open /root/res/cursor.png

[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[DEBUG]NVR [2]MGR debug = 601
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[1] Net out
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[18:49:21.348823] TSI_SetStatus:328: statue [3] -> [2] 2153
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
MGR:0- 639 .....
[7] I8S thread run ? = 9
[1] Net out
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
h[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[1] Net out
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[1] Net out
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[1] Net out
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[MAC.Ants_mac_Require.5148] req timeout
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
delete 1 nDelIdx = 0
delete 2 nStart = 0
delete 1 nDelIdx = 0
delete 2 nStart = 2
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
open /usr/etc/mycfg.xml

open /usr/etc/mycfg.xml

[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[1] Net out
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
MGR:0- 600 .....
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[1] Net out
[0] I8S thread run ? = 9
[1] I8S thread run ? = 9
[2] I8S thread run ? = 9
[3] I8S thread run ? = 9
[4] I8S thread run ? = 9
[5] I8S thread run ? = 9
[6] I8S thread run ? = 9
[7] I8S thread run ? = 9
[MAC.Ants_mac_Require.5148] req timeout

[AlienP666]

На сколько я помню этот рег на 3535 проце. Чип для сетевухи стоит отдельно. Проблемы с нерабочим LAN может быть три. Первая - корявая прошивка или прошивка от другой модели. Вторая - загнулся сетевой транс. Третья - проблема с чипом.

Я бы для начала проверил работает ли LAN когда делаем остановку при автобуте. Бывает так, что в погоне за лучшими возможностями, ставят не глядя прошивки, а они в реальности под другой тип регистратора. Итог регистратор вроде как работает, но после полной загрузки отваливается сетевуха. Порядок восстановления такого рега разжеван в теме про китайские miniNVR. Ссылки на различные юбуты и Хайтулы тоже там же. Важно!!! Сделать фото платы с двух сторон, серийный номер, ID Aeye если присутствует, и потом начинать все действия по восстановлению.

[yuri1958]

Прошивка стоит заводская. Как говорит клиент сеть перестала работать когда случайно подключили на ходу рег к PoE свитчу Теперь чип не хило греется. После остановки загрузки в uboot сети нет, пробовал в первую очередь. Транса такого на замену для проверки пока нет. Заказал чип с Али, буду ждать. Фото платы сделаю сегодня.

[AlienP666]

Возможно сожгли чип. Такое бывало когда подключали к PoE свитчу.

[Sonya]

Такое бывало когда подключали к PoE свитчу.

Значит, это был не настоящий PoE, без контроля выходов.

[yuri1958]

Такое бывало когда подключали к PoE свитчу.

Значит, это был не настоящий PoE, без контроля выходов.

Свитч там самый дешевый 100 мбит, 20 портов с PoE и 4 порта без PoE. Установщики сдали систему, взяли бабки, а заказчику лишь бы все работало.Сегодня установил новый NVR , все работает, предупредил чтобы не лазили сами где не надо.

[Boojin]

Здравствуйте!
Схожая ситуация, только проблема в другом. Чтобы не плодить тем напишу здесь.
Аналогичный регистратор только на четыре камеры NVR N6100-4EH.
Всё было отлично, смонтировано и запущено и год отработано на ура.
Но вот мне потребовалось зайти в рег и я не могу!......
Он работает, пишет, висит в сети и пингуется и воспроизводит удалённо, а вот локально его нет, не одна программа не видит его. А вот открыть его по IP адресу не могу, IE выдает "невозможно подключиться", другие браузеры вообще молчат. Пробовал другой комп, сеть, результат один и тот же.
Очень странно.
Есть видео входы VGA и HDMI, если к первому то монитор уходит в не поддерживаемый режим, а найти ко второму монитор не выходит.

Как возможно исправить или сбросить регистратор, есть ли способ?
Заранее спасибо за ответ!

[AlienP666]

Как возможно исправить или сбросить регистратор, есть ли способ?

Для начала найти FULL HD монитор или телевизор и сменить разрешение.