Кастылем.
Я особо не читал все команды, кто помнит последовательность, может посмотреть. И почему CV300 система? Вот так проходит цикл загрузки после официального обновления, до бесконечности. Плюс ошибка обновления на каком то модуле проходит.
OK
OK
Starting kernel ...
hi3516cv300 System startup
Uncompress.......Ok
hi3516cv300 System startup
U-Boot 2010.06-svn732 (Nov 13 2017 - 21:40:54)
Check Flash Memory Controller v100 ... Found
SPI Nor(cs 0) ID: 0x20 0x70 0x17
Block:64KB Chip:8MB Name:"XM25Q64AHIG"
at hifmc100_setTB() sr: 0x8 <<111>>.
lk[8 => 0x800000]
SPI Nor total size: 8MB
MMC:
EMMC/MMC/SD controller initialization.
Card did not respond to voltage select!
No EMMC/MMC/SD device found !
In: serial
Out: serial
Err: serial
Press Ctrl+C to stop autoboot
xmtech # printenv
bootcmd=setenv setargs setenv bootargs ${bootargs};run setargs;sf probe 0;sf read 83000000 30000 2E0000;squashfsload;bootm 0x82000000
bootdelay=1
baudrate=115200
ipaddr=192.168.1.10
serverip=192.168.1.107
netmask=255.255.0.0
gatewayip=192.168.1.1
bootfile="uImage"
da=mw.b 0x82000000 ff 1000000;tftp 0x82000000 u-boot.bin.img;sf probe 0;flwrite
du=mw.b 0x82000000 ff 1000000;tftp 0x82000000 user-x.cramfs.img;sf probe 0;flwrite
dr=mw.b 0x82000000 ff 1000000;tftp 0x82000000 romfs-x.cramfs.img;sf probe 0;flwrite
dw=mw.b 0x82000000 ff 1000000;tftp 0x82000000 web-x.cramfs.img;sf probe 0;flwrite
dl=mw.b 0x82000000 ff 1000000;tftp 0x82000000 logo-x.cramfs.img;sf probe 0;flwrite
dc=mw.b 0x82000000 ff 1000000;tftp 0x82000000 custom-x.cramfs.img;sf probe 0;flwrite
up=mw.b 0x82000000 ff 1000000;tftp 0x82000000 update.img;sf probe 0;flwrite
ua=mw.b 0x82000000 ff 1000000;tftp 0x82000000 upall_verify.img;sf probe 0;flwrite
tk=tftp 0x82000000 uImage;setenv setargs setenv bootargs ${bootargs};run setargs;bootm 0x82000000
dd=mw.b 0x82000000 ff 1000000;tftp 0x82000000 mtd-x.jffs2.img;sf probe 0;flwrite
bootargs=init=linuxrc mem=${osmem} console=ttyAMA0,115200 root=/dev/mtdblock1 rootfstype=squashfs mtdparts=hi_sfc:0x30000(boot),0x2E0000(romfs),0x300000(user),0x160000(web),0x40000(custom),0x50000(mtd)
osmem=40M
ethaddr=00:12:31:3d:14:9a
NID=0x0001
appSystemLanguage=SimpChinese
appVideoStandard=PAL
appNetIP=0x0A01A8C00x00FFFFFF0x0101A8C0
stdin=serial
stdout=serial
stderr=serial
verify=n
ver=U-Boot 2010.06-svn732 (Nov 13 2017 - 21:40:54)
Environment size: 1540/65532 bytes
xmtech # sf probe 0
8192 KiB hi_fmc at 0:0 is now current device
xmtech #
xmtech # printenv
bootcmd=setenv setargs setenv bootargs ${bootargs};run setargs;sf probe 0;sf read 83000000 30000 2E0000;squashfsload;bootm 0x82000000
bootdelay=1
baudrate=115200
ipaddr=192.168.1.10
serverip=192.168.1.107
netmask=255.255.0.0
gatewayip=192.168.1.1
bootfile="uImage"
da=mw.b 0x82000000 ff 1000000;tftp 0x82000000 u-boot.bin.img;sf probe 0;flwrite
du=mw.b 0x82000000 ff 1000000;tftp 0x82000000 user-x.cramfs.img;sf probe 0;flwrite
dr=mw.b 0x82000000 ff 1000000;tftp 0x82000000 romfs-x.cramfs.img;sf probe 0;flwrite
dw=mw.b 0x82000000 ff 1000000;tftp 0x82000000 web-x.cramfs.img;sf probe 0;flwrite
dl=mw.b 0x82000000 ff 1000000;tftp 0x82000000 logo-x.cramfs.img;sf probe 0;flwrite
dc=mw.b 0x82000000 ff 1000000;tftp 0x82000000 custom-x.cramfs.img;sf probe 0;flwrite
up=mw.b 0x82000000 ff 1000000;tftp 0x82000000 update.img;sf probe 0;flwrite
ua=mw.b 0x82000000 ff 1000000;tftp 0x82000000 upall_verify.img;sf probe 0;flwrite
tk=tftp 0x82000000 uImage;setenv setargs setenv bootargs ${bootargs};run setargs;bootm 0x82000000
dd=mw.b 0x82000000 ff 1000000;tftp 0x82000000 mtd-x.jffs2.img;sf probe 0;flwrite
bootargs=init=linuxrc mem=${osmem} console=ttyAMA0,115200 root=/dev/mtdblock1 rootfstype=squashfs mtdparts=hi_sfc:0x30000(boot),0x2E0000(romfs),0x300000(user),0x160000(web),0x40000(custom),0x50000(mtd)
osmem=40M
ethaddr=00:12:31:3d:14:9a
NID=0x0001
appSystemLanguage=SimpChinese
appVideoStandard=PAL
appNetIP=0x0A01A8C00x00FFFFFF0x0101A8C0
stdin=serial
stdout=serial
stderr=serial
verify=n
ver=U-Boot 2010.06-svn732 (Nov 13 2017 - 21:40:54)
Environment size: 1540/65532 bytes
xmtech #
